Site Search

Learn More About...

This item is not available for order online

Mains voltage: 120 V AC, 50/60 Hz
2-second safety time during operation
3-second trial for ignition period
Continuous self-testing for faults
Immediate fault lock-out or restart following flame failure available as a switchable function
Flame control with UV sensor or ionization sensor
Diverse installation possibilities via holes or snap mechanism for DIN rail
Display for program status and flame signal intensity
CSA, CE, AGA approvals

	FAQ: Kromschröder Product Labels and Type Codes (Blog Post)
	Burner Control IFD Brochure
	Burner Control IFD Operating Instructions
	Burner Control IFD Technical Sheet

Model and Description	Price	Cart
Ignition Cable Silicone Rubber Cable High Voltage 7mm (priced per foot).

Also see: UVS, TGI, and TZI

Click on images for close-up view.

	Forced draught burners Control: On/Off Gas valve and air valve are activated simultaneously. The burner is ignited and monitored by a single electrode. In the event of a flame failure, an immediate fault lock-out occurs.
	Two-stage-controlled burner Control: ON/OFF or ON/HIGH/LOW/OFF The burner BIO/BIC starts at low-fire rate. Once the normal operating state is reached, the automatic burner control unit for continuous operation IFD 258 will release control. The PLC can now pulse the air solenoid valve VR..R in order to control the capacity between high and low fire.
	Modulating-controlled burner Control: ON/OFF/continuous The PLC uses the actuator IC 20 to move the air butterfly valve BVA to ignition position. The burner BIO/BIC starts at low-fire rate. Once the normal operating state is reached, the PLC uses the actuator IC 20 and the air butterfly valve BVA to control the burner capacity.

General Specifications
Operating voltage:	120 V AC, -15/+10%, 50/60 Hz
Safety time on start-up:	3 sec.
Safety time during operation:	< 1sec. < 2 sec.
Ignition time:	approx. 2, 3 or 6 sec
Power consumption:	approx. 9 VA
Output voltage for valves and ignition transformer:	mains voltage
Ignition output:	max. 2 A, cos φ = 0.2
Valve output:	max. 1 A, cos φ = 1
Signalling contacts:	max. 2 A, 253 V AC
Max. number of operating cycles:	250,000
Max. number of operating cycles for Reset button:	1000
Max. number of operating cycles for Mains button:	1000
Signal inputs (110/120 V AC):	Signal "1": 80 - 126.5 V Signal "0": 0 - 20 V Frequency: 50/60 Hz.
Input current signal inputs:	Signal "1": typ. 2 mA.
Flame control sensor voltage:	approx. 230 V AC
Flame control sensor current:	> 1 µA
Flame control Max. sensor current:	ionization < 28 µA.
Ignition cable:	IFD 258: max. 5 m, recommended < 1 m (with TZI/TGI)
Permissible UV sensors:	Elster Kromschröder models UVS for ambient temperatures from -40 to +80°C (-40 to 176°F)
Valve connections:	1
Ignition current:	25 mA
Spark gap:	2 mm, max. 5 mm
Fuse in unit:	F1: T 3.15A H 250 V pursuant to IEC 127-2/5
Ambient temperature:	-20 to +60°C (-4 to +140°F)
Relative humidity:	no condensation permitted
Enclosure:	IP 54 pursuant to IEC 529. Overvoltage category III pursuant to EN 60730
Cable gland:	M16
Installation position:	any
Weight:	610 g (1.34 lbs.)